Daystar Rocker Switch Amber Light 20 AMP Single Pole

This "fits" into any of the 3 switch holes to the lower left of the steering wheel of a 2011 Lancer. However, the holes in the plastic panel piece will need to be shaved away on the sides until they fit. Once in, there is a ledge that covers up the cut marks on the panel, so no fear of horrible cutting work showing. It's too bad they aren't just a tad narrower, then no modifications would be needed. I am unsure about any other vehicle, but they work well in a 2011 Lancer and any other Lancer with the same setup.The light is bright enough to illuminate about a square foot around it on the dash and door. This may be TOO bright really, but I appreciate more lights since I have a hard time seeing at night anyway. When the switch is off, the light is off. When it is on, the light is on. The prongs on the back can hold size 16-14 electrical quick clips or whatever they are called. On the top and bottom are flexible ridged blades designed to hold the switch in once its pushed into a snug fitting. I power 2 of these on either side of the Lancer traction control switch, both powered from a tie in on the heated seat fuse and go out to 2 sets of LED's, a backup camera, and a 7 inch screen. No problems.

The Rugged Ridge side A-pillar switch pod will work with this switch. Rugged Ridge makes similar switches but I like the shape of these better. The directions that come with the switch are clear and so they are easy to connect. The power for the lamp light comes from the wire going to the relay. There is also one terminal on the back that needs to go to a ground connection. So there are three terminals on the back; Power In, Power Out, Lamp ground. The terminals are standard size and easy to connect terminals to. You will have to get your own terminals and wire; there is no wiring harness for the switches.The plastic for these switches seems a little light weight but other reviewers have indicated no long-term problems.

It looks great and lights up like the sun. Well built and looks fanstastic. However, if you have a wrangler from 03-06 (there isn't an ashtray next to the auxiliary outlets) it wont fit because it sits too far back into the dash and there is a little overhang that prevents it from fitting there. I ended up trying to trim it down, which required me to cut the top of the switch all the way down to where the light should be shining through for it to fit. It works but looks messy. So I'm ordering a new one and cutting out a place for it on the blank panel next to the switches

Daystar JK Panel: Fits snug, just right. Automatic transmission. Color matches as well. The stamped places for cut outs are easy to excise. INSTALL TIP -> I needed to use a chainsaw file to smooth out the edges/burs of the switch holes for a very clean fit. Would be five stars if came with its own set of clips.Switches: They toggle corectly, simple, straightforward, rated high enough to hard wire my accesories through them without a relay. The lighted part of the switch works correctly. My $0.02 is to mount the switches with the lighted side down, as the lighted switch can be bright at night.Bottomline after 6 months of use- I would purchase this again, and I am happy with the panel/switches.edit- after 2 years all switches working perfectly, no problems

I used two of these swtiches to fill the knockout slots located in the center console of my 4Runner. I use one to control the iSimple IS31 Universal Auxiliary Audio Input I installed and the other to control power to the radar detector I hard wired in. Both work flawlessy and look great. I pulled the 12 Volts right off the lighter socket and used a ground located in the console as well. As others have stated the slots had to be modified. I used a dremel tool and went to town on the the console and shaved away the ridge inside the solts, 5 mins worth of work. Great buy!

I purchased this switch to work in conjunction with an LED light bar I installed on under the ROPS of my zero turn mower. It comes with an easy to follow wiring diagram and was easy to install. I used the package insert/wiring diagram as a template to cut the hole on the mower next to the other gauges and switches.The switch has small "tabs" on each side that compress/expand when passed through the hole so be sure to cut too small at first. You can always cut more.The amber color is true. It matches the orange on my Kubota nicely.

These switches are very bright, and constructed well. The only reason I gave it 4 instead of 5 is because I mounted them on the dash where my knee can hit them entering the truck. The first time this happened... One of the 4 broke. Granted... My knee did it... But it still happened. It's a good enough item that I replaced it with the same exact switch.

Didn't install. Hoped they would fit my 2006 Toyota Tacoma in the stock slots for additional switches. It does not. Its close but you'll have to trim out the hole more than I was willing to do at this time.Tested the swtich and it worked. Light on switch was good brightness. Bright enough to let you know its on but not distracting bright.

These switches fit perfectly in the pre made mounting holes in my 2004 Nissan Pathfinder (where the seat heater switches would be located), I just popped the covers off and snapped the switches in. They match the colour and look factory

Works as advertised. However, if left on for 5 minutes, the illuminated light gets fairly warm.

Would purchase this again - product was great quality! As expected

👍

nice switch